A single-center study on the distribution and antibiotic resistance of pathogens causing bloodstream infection in patients with hematological malignancies / 中华血液学杂志

Objective: To study the incidence of bloodstream infections, pathogen distribution, and antibiotic resistance profile in patients with hematological malignancies. Methods: From January 2018 to December 2021, we retrospectively analyzed the clinical characteristics, pathogen distribution, and antibiotic resistance profiles of patients with malignant hematological diseases and bloodstream infections in the Department of Hematology, Nanfang Hospital, Southern Medical University. Results: A total of 582 incidences of bloodstream infections occurred in 22,717 inpatients. From 2018 to 2021, the incidence rates of bloodstream infections were 2.79%, 2.99%, 2.79%, and 2.02%, respectively. Five hundred ninety-nine types of bacteria were recovered from blood cultures, with 487 (81.3%) gram-negative bacteria, such as Klebsiella pneumonia, Escherichia coli, and Pseudomonas aeruginosa. Eighty-one (13.5%) were gram-positive bacteria, primarily Staphylococcus aureus, Staphylococcus epidermidis, and Enterococcus faecium, whereas the remaining 31 (5.2%) were fungi. Enterobacteriaceae resistance to carbapenems, piperacillin/tazobactam, cefoperazone sodium/sulbactam, and tigecycline were 11.0%, 15.3%, 15.4%, and 3.3%, with a descending trend year on year. Non-fermenters tolerated piperacillin/tazobactam, cefoperazone sodium/sulbactam, and quinolones at 29.6%, 13.3%, and 21.7%, respectively. However, only two gram-positive bacteria isolates were shown to be resistant to glycopeptide antibiotics. Conclusions: Bloodstream pathogens in hematological malignancies were broadly dispersed, most of which were gram-negative bacteria. Antibiotic resistance rates vary greatly between species. Our research serves as a valuable resource for the selection of empirical antibiotics.

Three-dimensional finite element analysis of cement flow in abutment margin-crown platform switching / 北京大学学报(医学版)

OBJECTIVE@#To analyze the cement flow in the abutment margin-crown platform switching structure by using the three-dimensional finite element analysis, in order to prove that whether the abutment margin-crown platform switching structure can reduce the inflow depth of cement in the implantation adhesive retention.@*METHODS@#By using ANSYS 19.0 software, two models were created, including the one with regular margin and crown (Model one, the traditional group), and the other one with abutment margin-crown platform switching structure (Model two, the platform switching group). Both abutments of the two models were wrapped by gingiva, and the depth of the abutment margins was 1.5 mm submucosal. Two-way fluid structure coupling calculations were produced in two models by using ANSYS 19.0 software. In the two models, the same amount of cement were put between the inner side of the crowns and the abutments. The process of cementing the crown to the abutment was simulated when the crown was 0.6 mm above the abutment. The crown was falling at a constant speed in the whole process spending 0.1 s. Then we observed the cement flow outside the crowns at the time of 0.025 s, 0.05 s, 0.075 s, 0.1 s, and measured the depth of cement over the margins at the time of 0.1 s.@*RESULTS@#At the time of 0 s, 0.025 s, 0.05 s, the cements in the two models were all above the abutment margins. At the time of 0.075 s, in Model one, the gingiva was squeezed by the cement and became deformed, and then a gap was formed between the gingiva and the abutment into which the cement started to flow. In Model two, because of the narrow neck of the crown, the cement flowed out from the gingival as it was pressed by the upward counterforce from the gingival and the abutment margin. At the time of 0.1 s, in Model one, the cement continued to flow deep inside with the gravity force and pressure, and the depth of the cement over the margin was 1 mm. In Model two, the cement continued to flow out from the gingival at the time of 0.075 s, and the depth of the cement over the margin was 0 mm.@*CONCLUSION@#When the abutment was wrapped by the gingiva, the inflow depth of cement in the implantation adhesive retention can be reduced in the abutment margin-crown platform switching structure.

A historical review of dental schools founded by dentist Situ Bo in modern time / 中华口腔医学杂志

About 8 dental schools were founded by Chinese dentists during modern times (1909-1949) in China. Only one still worked after the founding of the People's Republic of China, which was one of the three dental schools founded by dentist Situ Bo. There were no systematic researches on Situ Bo's participation in dentistry education. This paper analyzes the founder's experience in dentistry and in the two schools he founded at the beginning, focusing on the background and process of the schools' construction, management, teaching, teachers and students training, etc. The results show that the establishment of the first two dental schools have laid important foundation for the establishment and development of Shanghai Dental College by the reserve of trained professional teachers and accumulated valuable experience in running schools. The systematic review of this history will help us better understand the establishment and development of Shanghai Dental College and the efforts in dentistry education made by dentists growed up in modern China, as well as the early development process of stomatology.

Formation of professor Mao Xiejun's thoughts on stomatological education / 中华口腔医学杂志

Professor Mao Xiejun wrote a report about dental education of China in 1935. From 1948 to 1950, he published three articles containing the educational idea of "developing dentistry into stomatology". When he served as the director of the Faculty of Dentistry of Peking University Medical School in July 1950, he proposed to rename the Faculty of Dentistry into the Faculty of Stomatology,which were approved by the Ministry of Health and the Ministry of Education of the People's Republic of China in one month. The Chinese Medical Association established the Society of Stomatology the next year. Later, dentistry was successively changed into stomatology, and medical content was integrated into dental education, which was of great significance and far-reaching influence. During the developments of the thought of stomatological education in China, Professor Mao Xiejun evidently played a pivotal role. In this paper, the formation process of the thoughts of stomatological education related to professor Mao Xiejun's contribution is elucidated through studying the archives, personal letters, and historical documents, so as to enrich the researches on the history of stomatology in China and to facilitate better understanding and promoting the development of stomatology.

Regulation of ischemic stroke by circadian rhythm and intervention by traditional Chinese medicine / 中国中药杂志

Circadian rhythm is an internal regulatory mechanism formed in organisms in response to the circadian periodicity in the environment, which modulates the pathophysiological events, occurrence and development of diseases, and the response to treatment in mammals. It significantly influences the susceptibility, injury, and recovery of ischemic stroke, and the response to therapy. Accumulating evidence indicates that circadian rhythms not only regulate the important physiological factors of ischemic stroke events, such as blood pressure and coagulation-fibrinolysis system, but also participate in the immuno-inflammatory reaction mediated by glial cells and peripheral immune cells after ischemic injury and the regulation of neurovascular unit(NVU). This article aims to link molecular, cellular, and physiological pathways in circadian biology to the clinical consequences of ischemic stroke and to illustrate the impact of circadian rhythms on ischemic stroke pathogenesis, the regulation of NVU, and the immuno-inflammatory responses. The regulation of circadian rhythm by traditional Chinese medicine is reviewed, and the research progress of traditional Chinese medicine intervention in circadian rhythm is summarized to provide a reasonable and valuable reference for the follow-up traditional Chinese medicine research and molecular mechanism research of circadian rhythm.

Prediction, analysis and application of learning curve of tooth preparation for all ceramic crowns of maxillary central incisors / 北京大学学报(医学版)

OBJECTIVE@#To predict the learning curve of tooth preparation for all ceramic crowns of maxillary central incisors on phantom head simulators for graduate students participating in standardized dental resident training based on the modified Wright learning curve model, then to analyze and applicate the learning curve.@*METHODS@#Twelve graduate students participating in standardized dental resident training were selected to prepare the resin maxillary central incisors on phantom head simulators for all ceramic crowns 4 times. The results of preparation were evaluated by 3 prosthetic experts with at least 10 years' experience focusing on the reduction, contour, taper, shoulder, finish line, margin placement, adjacent tooth injury, and preparation time for tooth preparation. The learning rate of tooth preparation was calculated by scores of tooth preparation of 4 times. The learning curve of tooth preparation was predicted based on the modified Wright learning curve model. According to the criteria of standardized training skill examinations for dental residents in Beijing, 80 was taken as the qualified standard score. The minimum training times for tooth preparation to satisfy the qualified standard score (80) was calculated, to analyze the characteristics of learning curve and evaluate the effectiveness of tooth preparation.@*RESULTS@#The scores of 4 tooth preparation were 64.03±7.80, 71.40±6.13, 74.33±5.96, and 75.98±4.52, respectively. The learning rate was (106±4)%, which showed the learning curve an upward trend. There were no significant differences between the qualified standard score and the predicted scores of tooth preparation from the 5th preparation to the 13th preparation (P > 0.05). The predicted score of the 14th preparation was higher than the qualified standard score (P < 0.05).@*CONCLUSION@#The trend of the learning curve of tooth preparation for all ceramic crowns of maxillary central incisors on phantom head simulators for graduate students participating in standardized dental resident training is upward, which predicts the minimum training times higher than the qualified standard score is 14 times.

Prognostic significance of IKZF1 gene deletions in patients with B-cell acute lymphoblastic leukemia / 中华血液学杂志

Objective: This study aimed to investigate the prognostic significance of IKZF1 gene deletion in patients with acute B lymphoblastic leukemia (B-ALL) . Methods: The clinical data of 142 patients with B-ALL diagnosed in Nanfang Hospital between March 2016 and September 2019 were analyzed. Results: IKZF1 deletion was found in 36.0% of the 142 patients with B-ALL, whereas exon 4-7 deletion was found in 44.0% . White blood cell counts were higher in patients with the IKZF1 deletion (52.0% and 28.3% , P=0.005) ; these patients also experienced worse effects of mid-term induction therapy (40.0% and 70.7% , P<0.001) and had a higher proportion of Philadelphia chromosome-positive (52.0% and 21.7% , respectively, P<0.001) . Univariate analysis revealed that the 3-year overall survival rate (OS) and event-free survival rate (EFS) in the IKZF1 deletion group were significantly lower than the IKZF1 wild-type group [ (37.1±7.3) % vs (54.7±5.4) % , (51.8±7.9) % vs (73.9±4.7) % ; P=0.025, 0.013, respectively]. Multivariable analysis showed that harboring IKZF1 deletion was an adverse factor of EFS and OS (HR=1.744, 2.036; P=0.022, 0.020, respectively) . Furthermore, the IKZF1 deletion/chemotherapy group had significantly lower 3-year OS, EFS, and disease-free survival rates than other subgroups. In the IKZF1 deletion cohort, allo-hematopoietic stem cell transplantation (HSCT) significantly improved OS and EFS compared to non-allo-HSCT[ (67.9±10.4) % vs (31.9±11.0) % , (46.6±10.5) % vs (26.7±9.7) % ; P=0.005, 0.026, respectively]. Conclusion: Pediatric-inspired chemotherapy was unable to completely reverse the negative effect of IKZF1 deletion on prognosis. Pediatric-inspired regimen therapy combined with allo-HSCT, in contrast, significantly improved the overall prognosis of IKZF1 deletion B-ALL.

Oxytocin-induced endothelial nitric oxide dependent vasorelaxation and ERK1/2-mediated vasoconstriction in the rat aorta

Oxytocin is a neuropeptide produced primarily in the hypothalamus and plays an important role in the regulation of mammalian birth and lactation. It has been shown that oxytocin has important cardiovascular protective effects. Here we investigated the effects of oxytocin on vascular reactivity and underlying the mechanisms in human umbilical vein endothelial cells (HUVECs) in vitro and in rat aorta ex vivo. Oxytocin increased phospho-eNOS (Ser 1177) and phospho-Akt (Ser 473) expression in HUVECs in vitro and the aorta of rat ex vivo. Wortmannin, a specific inhibitor of phosphatidylinositol 3-kinase (PI3K), inhibited oxytocin-induced Akt and eNOS phosphorylation. In the rat aortic rings, oxytocin induced a biphasic vascular reactivity: oxytocin at low dose (10-9–10-8 M) initiated a vasorelaxation followed by a vasoconstriction at high dose (10-7 M). L-NAME (a nitric oxide synthase inhibitor), endothelium removal or wortmannin abolished oxytocin-induced vasorelaxation, and slightly enhanced oxytocin-induced vasoconstriction. Atosiban, an oxytocin/ vasopressin 1a receptor inhibitor, totally blocked oxytocin-induced relaxation and vasoconstriction. PD98059 (ERK1/2 inhibitor) partially inhibited oxytocin-induced vasoconstriction. Oxytocin also increased aortic phospho-ERK1/2 expression, which was reduced by either atosiban or PD98059, suggesting that oxytocin-induced vasoconstriction was partially mediated by oxytocin/V1aR activation of ERK1/2. The present study demonstrates that oxytocin can activate different signaling pathways to cause vasorelaxation or vasoconstriction. Oxytocin stimulation of PI3K/eNOS-derived nitric oxide may participate in maintenance of cardiovascular homeostasis, and different vascular reactivities to low or high dose of oxytocin suggest that oxytocin may have different regulatory effects on vascular tone under physiological or pathophysiological conditions.

Preliminary clinical application verification of complete digital workflow of design lips symmetry reference plane based on posed smile / 北京大学学报(医学版)

OBJECTIVE@#To automatically construct lips symmetry reference plane (SRP) based on posed smile, and to evaluate its advantages over conventional digital aesthetic design.@*METHODS@#Eighteen subjects' three-dimensional facial and dentition data were gathered in this study. The lips SRP of experimental groups were used with the standard weighted Procrustes analysis (WPA) algorithm and iterative closest point (ICP), respectively. A reference plane defined by experts based on regional ICP algorithm, served as the truth plane. The angle error values between the lips SRP of WPA algorithm in the experimental groups and the truth plane were evaluated in this study, and the lips SRP of ICP algorithm of the experimental groups was calculated in the same way. The lips SRP based on posed smile as a reference for aesthetic design and evaluate preliminary clinical application.@*RESULTS@#The average angle error between the lips SRP of WPA algorithm and the truth plane was 1.78°±1.24°, which was smaller than that between the lips SRP of ICP and the truth plane 7.41°±4.31°. There were significant differences in the angle errors among the groups (P < 0.05). In the aesthetic design of anterior teeth, automatically constructing the lips SRP of WPA algorithm based on posed smile and the original symmetry plane by re-ference compared with the prosthetic design, the subjects' scores on the lips SRP of WPA algorithm based on posed smile (8.48±0.57) were higher than those on the original symmetry plane (5.20±1.31).@*CONCLUSION@#Automatically constructing the lips SRP of WPA algorithm based on posed smile was more accurate than ICP algorithm, which was consistent with the truth plane. Moreover, it can provide an important reference for oral aesthetic diagnosis and aesthetic analysis of the restoration effect. In the aesthetic design of anterior teeth, automatically constructing the lips SRP of WPA algorithm based on posed smile can improve the patients' satisfaction in esthetic rehabilitation.

Finite element analyses of retention of removable partial denture circumferential clasps manufactured by selective laser melting / 北京大学学报(医学版)

OBJECTIVE@#To compare the retentions of different designs of cobalt-chromium (Co-Cr), pure titanium (CP Ti), and titanium alloy (Ti-6Al-4V) removable partial denture (RPD) circumferential clasps manufactured by selective laser melting (SLM) and to analyze the stress distribution of these clasps during the removal from abutment teeth.@*METHODS@#Clasps with clasp arm size A (1.9 mm width/1.1 mm thickness at the body and 0.8-taper) or B (1.2 times A) and 0.25 mm or 0.50 mm undercut engagement were modeled on a prepared first premolar die, named as designs A1, A2, A3, and A4, respectively. The density and elastic modulus of SLM-built Co-Cr, CP Ti, and Ti-6Al-4V were measured and given to different groups of clasps. The density, elastic modulus, and Poisson ' s ratio of enamel were given to the die. The control group was the cast Co-Cr clasp with design A1, to which the density and elastic modulus of cast Co-Cr alloy were given. The Poisson's ratio of all metals was 0.33. The initial 5 N dislodging force was applied, and the maximum displacement of the clasp along the insertion path was computed. The load was reapplied with an increment of 5 N than in the last simulation until the clasp was completely dislodged. The retentive force range of different groups of clasps was obtained. The retentive forces of the SLM-built Co-Cr, CP Ti, and Ti-6Al-4V clasps with equivalent computed retentive force range to the control group were validated through the insertion/removal experiment. The von Mises stress distributions of these three groups of SLM-built clasps under 15 N loads were analyzed.@*RESULTS@#SLM-built Co-Cr, CP Ti, and Ti-6Al-4V clasps with designs B1 or B2, and Co-Cr clasps with design A2 had higher retentive forces than those of the control group. SLM-built CP Ti and Ti-6Al-4V clasps with design A1 had lower retentive forces than those of the control group. SLM-built Co-Cr clasp with design A1 and SLM-built CP Ti and Ti-6Al-4V clasps with design A2 had equivalent retentive forces to those of the control group. The insertion/removal experiment showed that the measured retentive forces of these three groups of SLM-built clasps were (21.57±5.41) N, (19.75±4.47) N, and (19.32±2.04) N, respectively. No statistically significant measured retentive force difference was found among these three groups of SLM-built clasps (P>0.05). The maximum von Mises stress of these three groups of SLM-built clasps exceeded their responding yield strength except for the Ti-6Al-4V one.@*CONCLUSION@#SLM-built Co-Cr circumferential clasps had higher retention than CP Ti and Ti-6Al-4V ones with the same clasp arm size and undercut engagement. The retention of SLM-built circumferential clasps could be adjusted by changing the undercut engagement and clasp arm size. If SLM-built circumferential clasps are used in clinical practice, the Ti-6Al-4V clasp with clasp arm size A and 0.50 mm undercut engagement is recommended considering the long-term use of RPD in the patient's mouth.

Clinical outcome of single posterior implant-supported monolithic zirconia crowns fabricated using full digital workflow and conventional workflow: a 3-year follow-up / 中华口腔医学杂志

Objective: To compare the clinical performance of posterior single implant-supported monolithic zirconia crowns fabricated by full digital workflow and that of those fabricated by conventional workflow. Methods: This is prospective clinical research. Thirty-five patients who participated in a previous study during August 2017 to October 2018 at Department of Prosthodontics, Peking University School and Hospital of Stomatology were included in this 3-year follow-up study. The 35 patients, 17 females and 18 males, aged (49.0±15.4) years (24-86 years old), was allocated into two groups. In the full digital workflow group, intraoral scanning was taken immediately after implant placement, and a full zirconia implant crown was fabricated using model-free computer aided design/computer aided manufacturing (CAD/CAM) procedure (n=14). In the conventional group, a conventional impression was taken 3 months after implant placement and the stone model was produced. A full zirconia implant crown was fabricated using conventional model-based procedure (n=21). Three years following crown delivery, all the prostheses were evaluated in the aspect of color, surface roughness, contour and marginal integrity using modified US Public Health Service criteria (MUSPHS criteria). The soft and hard tissue around implant was evaluated using modified plaque index, probing depth (PD), number of implants with bleeding on probing, marginal bone loss (MBL). The biological and mechanical complication were also recorded. Statistical analysis was performed using independent samples t test, Mann-Whitney U test and Fisher's exact test. Results: The total survival rate of prosthesis and implant was 100% (35/35). No significant difference in MUSPHS criteria ratings on color, surface roughness, contour and marginal integrity of these crowns were found between the full digital workflow group and the conventional group (P>0.05). Sixteen out of the 35 crowns had a contour score of B due to loss of interproximal contact. Ten out of the 35 crowns had the screw hole sealing resin sinking or falling off, four in the full digital workflow group and six in the conventional group. There was no significant difference in the rate of prostheses mechanical complications between the two groups (P=1.000). For all the implants, there was no significant difference in MBL, PD, the modified plaque index, and number of implants with bleeding on probing between the two groups (U=119.50,133.00,142.50, t=-0.53, P>0.05). Conclusions: The clinical performance of implant-supported posterior single monolithic zirconia crowns fabricated by full digital workflow was stable. There was no significant difference in the clinical performance of the single implant crowns between the full digital workflow group and the conventional group.

Application and research progress of digital virtual simulated design in dental esthetic rehabilitation / 中华口腔医学杂志

In dental esthetic rehabilitation, patients pay great attention to the rehabilitative esthetic effect before teeth preparation, and this is also an important content of doctor-patient communication. Along with the development and combined application of intraoral scan, three-dimensional (3D) face scan, digital design, numerical control machining and 3D printing technology, digital technology is gradually applied to the virtual simulated design before irreversible operation in dental esthetic rehabilitation. Digital technology can be used in dentistry to simulate the esthetic outcome in advance, to assist communication among the dentists, patients and dental technicians, and to realize satisfactory outcome in the final restorations precisely, which, as a result, increases the clinical satisfaction. This review focuses on the application of digital virtual simulated design technology in dental esthetic rehabilitation, analyzes the current research development, deficiency and future prospects, so as to provide guidance for clinical diagnosis and treatment.

Surveillance and response: The core intervention for malaria control during the post-elimination phase in China / 中国血吸虫病防治杂志

China was certified malaria-free by the WHO on June, 2021. Nevertheless, there are thousands of overseas imported malaria cases annually in China, and there are deaths of imported malaria cases reported every year in the country. In addition, there are secondary cases of imported malaria, and malaria vectors remain in regions where malaria were formerly endemic, resulting in a high risk of local transmission of imported malaria in eliminated regions in China. This article analyzes the risk of malaria control and the challenges of malaria surveillance and response during the post-elimination stage in China, and proposes some suggestions for future priorities.

Effects of mindfulness training on emotion and acceptance for people with disabilities: a systematic review / 中国康复理论与实践

@#Objective To systematically review the effect of mindfulness training on emotion and acceptance for people with disabilities. Methods From Web of Science, EBSCO, APA PsycInfo, Psychology and Behavioral Sciences Collection, Medline, CNKI, and Wanfang Data, researches about mindfulness training for people with disabilities were searched, from January 1st, 2010 to November 31st, 2020. The researches were screened, assessed the qualities and extracted data of included studies, and then, systematicaly reviewed. Results Fifteen researches were revealed, including 64 samples and 1065 participants. People with mental, intellectual, physical and speech disabilities were involved. Mindfulness-based cognitive therapy, mindfulness-based stress reduction, mindfulness-based Taiji Quan and mindfulness-based Yoga were commonly used. The effect of mindfulness training on people with disabilities were mainly reflected in the decrease of anxiety and depression, and the improvement of the acceptance for negative experiences. Conclusion Mindfulness training can help to improve the negative emotions and psychological acceptance for people with disabilities, thereby promoting physical and mental health and the quality of life.

Research progress on pesticide residues of Angelicae Sinensis Radix / 中国中药杂志

The demand for Angelicae Sinensis Radix, the dry root of Angelica sinensis, has been increasing year by year. However, the continuous cropping obstacles, frequent occurrence of pests and diseases, overuse of chemical pesticides, excessive pesticide residues and other problems in Angelicae Sinensis Radix production have attracted much attention. In this paper, we summarized the common diseases and pests attacking Angelica sinensis as well as the detection methods and characteristics of pesticide residues in Angelicae Sinensis Radix from 2002 to 2021. Additionally, we compared the limit standards of pesticide residues in Angelicae Sinensis Radix in and out of China and put forward suggestions for the high-quality and green development of Angelicae Sinensis Radix industry conside-ring the existing problems. The pesticide residues in Angelicae Sinensis Radix have been changing from organochlorines to organophosphorus pesticides. In recent years, some organophosphorus pesticides such as phorate, phoxim, isofenphos-methyl, phorate-sulfoxide, fenamiphos, isocarbophos, omethoate, and triazophos in Angelicae Sinensis Radix have seriously exceeded the standards. The detection methods of pesticide residues has evolved from chromatography to high performance chromatography-mass spectrometry, gas chromatography-mass spectrometry(GC-MS), and liquid chromatography-mass spectrometry(LC-MS), and some new detection techniques such as immunoassay have also been applied. Pesticide residues have become a primary factor that restricting the development of Angelicae Sinensis Radix industry. Therefore, moderate application of pesticides, establishment of ecological planting system, and strict limit standards of pesticide residues are necessary to solve the pesticide residue problem.

Imageology study of correlation loss and its related factors after short-segment pedicle screw reduction and fixation for lumbar fractures / 中国骨伤

OBJECTIVE@#To analyze the correction loss after posterior segmental fixation for lumbar spine fractures and explore the related image factors.@*METHODS@#Posterior short-segment fixation was received in 48 patients with L@*RESULTS@#The average follow-up was 12 to 18 (16.13±5.39) months. LKA, AVH and VWA at 1 week postoperative and those at the final follow up, were significantly improved compared with those preoperative (@*CONCLUSION@#The angle of adjacent intervertebral discs and anterior height of injured vertebrae were lost statistically after posterior short-segment pedicle screw treatment for lumbar fractures, and multivariate analysis showed that all of them were correlated with load-sharing score.

Studies on blood enrichment and anti-tumor effects of combined Danggui Buxue Decoction, Fe and rhEPO based on colon cancer-related anemia model and gut microbiota modulation / 中国天然药物

Colon cancer-related anemia (CCRA) is mainly caused by systemic inflammation, intestinal bleeding, iron deficiency and chemotherapy-induced myelosuppression in colon cancer. However, the best therapeutic schedule and related mechanism on CCRA were still uncertain. Studies on blood enrichment and anti-tumor effects of combined Danggui Buxue Decoction (DBD), Fe and rhEPO based on CCRA and gut microbiota modulation were conducted in this paper. Here, CCRA model was successfully induced by subcutaneous inoculation of CT-26 and i.p. oxaliplatin, rhEPO + DBD high dosage + Fe (EDF) and rhEPO + DBD high dosage (ED) groups had the best blood enrichment effect. Attractively, EDF group also showed antitumor activity. The sequencing results of gut microbiota showed that compared to P group, the relative abundances of Lachnospiraceae and opportunistic pathogen (Odoribacter) in ED and EDF groups were decreased. Interestingly, EDF also decreased the relative abundances of cancer-related bacteria (Helicobacter, Lactococcus, Alloprevotella) and imbalance-inducing bacteria (Escherichia-Shigella and Parabacteroides) and increased the relative abundances of butyrate-producing bacteria (Ruminococcaceae_UCG-014), however, ED showed the opposite effects to EDF, this might be the reason of the smaller tumor volume in EDF group. Our findings proposed the best treatment combination of DBD, rhEPO and Fe in CCRA and provided theoretical basis and literature reference for CCRA-induced intestinal flora disorder and the regulatory mechanism of EDF.

Clinical application and research progress of digital complete denture / 华西口腔医学杂志

Digital technologies use high-precision three-dimensional scanning, intelligence-aided design software, and multi-axis numerical control milling or 3D printing, which can produce restorations with reliable precision and suitable function. However, the development of digital technologies in the field of complete denture restoration has been slow due to the complexity of prosthesis. This review article introduces the current research status and clinical applications of digital complete dentures in prosthodontic clinics and dental laboratories to provide beneficial references to prosthodontists and dental technicians.

Evaluation of methods for fitness of removable partial denture / 北京大学学报(医学版)

OBJECTIVE@#To compare the differences and indications of three evaluation methods for fitness evaluation of removable partial denture (RPD).@*METHODS@#A RPD was fabricated and seated on the stone cast of a partially edentulous mandible, and the spaces between RPD and stone cast were recorded with polyvinyl siloxane (PVS) impression material forming PVS replicas. Using cross sectional measurement, the average thicknesses of PVS replicas were measured under stereomicroscope with different numbers of selected measuring points in the denture base, major connector, occlusal rest of the RPD, and the average thicknesses of the PVS replicas measured with different numbers of measuring points were compared using one-way analysis of variance (ANOVA) and independent sample t test. Three kinds of method, including cross sectional measurement, three-dimensional analysis on the stone cast, and three-dimensional analysis on the polyether cast, were applied to measure the average thicknesses of the PVS replicas, and the average thicknesses of the PVS replicas measured by these three evaluation methods were compared with ANOVA.@*RESULTS@#For cross sectional measurement, statistically significant differences were found in the average thicknesses of the PVS replicas in the denture base and the major connector among the different numbers of measuring points (P < 0.05), but no differences were found in the average thicknesses of the PVS replicas in the occlusal rest (P>0.05). There were significant differences among the average thicknesses of the PVS replicas measured by these three evaluation methods in each component of the RPD (P < 0.01). The average thickness measured by three-dimensional analysis on the stone cast and three-dimensional analysis on polyether cast were smaller than that measured by cross sectional measurement (P < 0.05). And there were no differences between the average thicknesses of PVS replicas measured by three-dimensional analysis on stone cast and three-dimensional analysis on polyether cast (P>0.05).@*CONCLUSION@#For cross sectional measurement, the average thickness of the PVS replicas was influenced by the number of measuring points, and the measurement accuracy of cross sectional measurement was not reliable enough. Three-dimensional analysis on stone cast which is suitable for evaluation in vitro and three-dimensional analysis on polyether cast which is suitable for evaluation in vivo can evaluate the fitness of RPD more comprehensively and effectively than that of cross sectional measurement.

Evaluation of fracture strength of two kinds of zirconia all-ceramic crowns with different edge compensation angles / 北京大学学报(医学版)

OBJECTIVE@#To evaluate the effects of different edge compensation angles on the fracture strength of multilayer zirconia all-ceramic crowns and traditional uniform zirconia all-ceramic crowns.@*METHODS@#The resin tooth preparation specimen of the mandibular first molar with a knife-edge was fabricated. A 3D digital model of the specimen was obtained by scanning it with a 3D dental model scanner. The 3D digital model was imported into computer aided design (CAD) software, and three 3D digital models of the full crown with the same surface shape are designed with the edge compensation angles of 30°, 45° and 60°, respectively. Then, the designed 3D digital model is imported into computer aided manufacturing (CAM) software. Three kinds of multilayer and homogeneous zirconia all-porcelain crowns with different edge compensation angles were fabricated, 10 each for a total of 60. The fracture load of each crown was measured under the electronic universal testing machine.@*RESULTS@#Fracture load of multilayer and uniform zirconia all-ceramic crowns, (4 322.86±610.07) N and (5 914.12±596.80) N in the 30° group, (5 264.82±883.76) N and (5 220.83±563.38) N in the 45° group and (4 900.42±345.41) N and (5 050.22±560.24) N in the 60° group, respectively. The fracture load of multi-layer zirconia all-ceramic crowns in the 30° group was significantly lower than that of homogeneous zirconia all-ceramic crowns(P < 0.05); there was no statistical significance in 45° group and 60° group(P>0.05). In the multi-layer zirconia all-ceramic crowns: the fracture load of the 30° group was significantly lower than that of the 45° group (P < 0.05); there was no significant difference between the 30° group and the 60° group, the 45° group and the 60° group (P>0.05).In uniform zirconia full crown group: the 30° group was higher than the 45° group, the 30° group was higher than the 60° group (P < 0.05), and there was no significant difference between the 45° group and the 60° group (P>0.05).@*CONCLUSION@#The fracture loads of three kinds of uniform and multilayer zirconia all ceramic crowns with different edge compensation angles can meet the clinical requirements. A smaller edge compensation angle is recommended when using traditional zirconia all-ceramic crowns, while 45° is recommended when using multi-layer zirconia all-ceramic crowns.